Basic Info.
Model NO.
DCE116FHM-N86-400
Usage
HMI/Smart Locker/Mobile Robots
Digital LCD Module Type
TFT-LCD Module
Touch Screen Type
Capacitive
DOT-Matrix Graphic LCD Module Type
RGB Vertical Stripe Arrangement
LCD Drive Mode
Multiplex Drive LCD Module
Active Area
256.32(H) ×144.18(V) mm
Pixel Format
1920(H) ×1080(V)
Pixel Pitch
0.1335(H) X 0.1335 (V)
Pixel Configuration
R, G, B Vertical Stripe
Display Mode
Normally Black
Surface Treatment of Front Polarizer
Anti-Glare Coating: (3h)
Transport Package
Carton Box
Specification
Industrial-grade LCD display module
Product Description
1. Application
This specification applies to a color TFT-LCD Module,
2. Overview
This Open-cell is a color active matrix LCD open-cell incorporating Oxide TFT (Thin Film Transistor).It is composed of a color TFT-LCD panel, driver ICs, a control circuit and power supply circuit. Graphics and
texts can be displayed on a 1920×3×1080 dots panel with 16,777,216 colors by using eDP (Embedded Display Port) Ver1.2 interface and supplying +3.3V DC supply voltage for TFT-LCD panel driving.
In this TFT-LCD panel, color filters for excellent color performance is incorporated to realize brighter and clearer pictures, making this open-cell optimum for use in multi-media applications. Optimum viewings are in all directions.
Without Backlight-driving LED controller.
eDP transfer rate specification: 2.7Gbps/2 lane. 3.Mechanical specifications.
| Parameter | Specification | Unit |
|---|
| Display size | 11.6" (Diagonal) | inch |
| Active area | 256.32(H) ×144.18(V) | mm |
| Pixel Format | 1920(H) ×1080(V) (1pixel = R + G + B dot) | pixel |
| Pixel pitch | 0.1335(H) × 0.1335 (V) | mm |
| Pixel configuration | R, G, B vertical stripe | |
| Display mode | Normally black | |
| Surface treatment of front polarizer | Anti-glare coating: (3H) | |
Outline dimensions| Parameter | | Min | Typ | Max | Unit | Remark |
|---|
| Unit outline dimensions | Width | 263.3 | 263.5 | 263.7 | mm | |
| | Height | 157.12 | 157.32 | 157.52 | mm | |
| | Depth | 2.45 | 2.55 | 2.75 | mm | w/o PWB.[Note3-2] |
| Mass | | - | - | - | g | |
| Parameter | Conditions | Min. | Typ. | Max. | Unit |
|---|
| Viewing Angle (CR>10) | Horizontal (θL) | - | 89 | - | degree |
| Viewing Angle (CR>10) | Horizontal (θR) | - | 89 | - | degree |
| Viewing Angle (CR>10) | Vertical (θT) | - | 89 | - | degree |
| Viewing Angle (CR>10) | Vertical (θB) | - | 89 | - | degree |
| Contrast Ratio | Center | 700 | 1000 | - | - |
| Response Time | Tr+Td | - | 25 | - | ms |
| CF Color Chromaticity (CIE1931) | Red x | Typ. -0.05 | TBD | Typ. +0.05 | - |
| CF Color Chromaticity (CIE1931) | Red y | Typ. -0.05 | TBD | Typ. +0.05 | - |
| CF Color Chromaticity (CIE1931) | Green x | Typ. -0.05 | TBD | Typ. +0.05 | - |
| CF Color Chromaticity (CIE1931) | Green y | Typ. -0.05 | TBD | Typ. +0.05 | - |
| CF Color Chromaticity (CIE1931) | Blue x | Typ. -0.05 | TBD | Typ. +0.05 | - |
| CF Color Chromaticity (CIE1931) | Blue y | Typ. -0.05 | TBD | Typ. +0.05 | - |
| CF Color Chromaticity (CIE1931) | White x | - | (0.313) | - | - |
| CF Color Chromaticity (CIE1931) | White y | - | (0.329) | - | - |
| NTSC ratio | % | - | (72) | - | - |
| Luminance of white | YL | 360 | 400 | - | cd/m² |
| White uniformity 13pt | δw | =0 | 1.3 | 1.5 | - |
Be sure to turn off the power supply when inserting or disconnecting the cable.
Please insert for too much stress not to join a connector in the case of insertion of a connector.
Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist.
Since the front polarizer is easily damaged, pay attention not to scratch it.
Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care.
Since CMOS LSI is used in this module, take care of static electricity and injure the human earth when
handling. Observe all other precautionary requirements in handling components.
This module has its circuitry PCBs on the side and should be handled carefully in order not to be stressed.
Laminate film is attached to the module surface to prevent it from being scratched. Peel the laminate film off
slowly just before the use with strict attention to electrostatic charges. Ionized air shall be blown over during
the action. Blow off the 'dust' on the polarizer by using an ionized nitrogen gun, etc. Working under the
following environments is desirable.
All workers wear conductive shoes, conductive clothes, conductive fingerstalls and grounding belts without ail.
Use Ionized blower for electrostatic removal, and peel of the laminate film with a constant speed. (Peeling of it at over 2 seconds)
The polarizer surface on the panel is treated with Anti-Glare. In case of attaching protective board over the LCD, be careful about the optical interface fringe etc. which degrades display quality.
Do not expose the LCD module to a direct sunlight, for a long period of time to protect the module from the ultra violet ray.
When handling LCD modules and assembling them into cabinets, please be noted that long-term storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive,resin, etc. which generate these gasses, may cause corrosion and discoloration of the LCD modules.
Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets inside your eye or mouth by mistake.
Disassembling the module can cause permanent damage and should be strictly avoided.
Please don't remove the fixed tape, insulating tape etc that was pasted on the original module.(Except for protection film of the panel.)
Be careful when using it for long time with fixed pattern display as it may cause afterimage.(Please use a screen saver etc., in order to avoid an afterimage.)
If a minute particle enters in the module and adheres to an optical material, it may cause display nonuniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you intend to install a fan.
Epoxy resin (amine series curing agent), silicone adhesive material (dealcoholization series and oxime series), tray forming agent (azo compound) etc, in the cabinet or the packing materials may induce abnormal display with polarizer film deterioration regardless of contact or noncontact to polarizer film. Be sure to confirm the component of them.
Do not use polychloroprene. If you use it, there is some possibility of generating Cl2 gas that influences the reliability of the connection between LCD panel and driver IC.
Do not put a laminate film on LCD module, after peeling of the original one. If you put on it, it may cause discoloration or spots because of the occurrence of air gaps between the polarizer and the film.
Ground module bezel to stabilize against EMI and external noise.
When you peel off the protection film
-Be sure to peel off slowly(recommended more than 5sec) and constant speed
-Peeling direction shows the following Figure
-Be sure to ground person with adequate methods such as the anti-static wrist band.
-Be sure to ground all terminals of the PWB connector while peeling of the protection film.
-Ionized air should be blown over during peeling action.
-The protection film must not touch driver-ICs, PWB and all components on PWB.
-If adhesive may remain on the polarizer after the protection film peeling off , please remove with isopropyl alcohol.
Address:
Room 1701c1, Block a, Fencheng Zhigu Building, No. 60 Tiezai Road, Xixiang Street, Bao'an District, Shenzhen, Guangdong, China
Business Type:
Manufacturer/Factory
Business Range:
Consumer Electronics, Electrical & Electronics
Management System Certification:
ISO 9001, ISO 14001, IATF16949
Company Introduction:
Shenzhen David Camp Electronics Co., Ltd founded in Shenzhen, a global hub for hardware innovation, we have beendeeply involved in the industrial display field for many years and are a corestrategic partner of BOE (Beijing Oriental Electronics Co., Ltd. ) for LCD screens.
Our core business is the R&D and manufacturing of LCD screen assemblymodules. We focus on industrial-grade display solutions, providinghigh-precision, high-reliability, and scenario-adaptive display technologies forindustrial control, medical, smart terminals, and 3D interaction in portabledevices.
We utilize Chengyi 802A fully automatic bonding line, Eurolink semi-automaticbonding line, COG fully automatic bonding, FOG fully automatic bonding, FOGfully automatic dispensing machine, FOB drying machine, and FOBsemi-automatic pressing machine.
